View XP1044-QL-EV1_4142835.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

4.9-5.9 GHz 3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
P1044-QL Features
P1dB, 34.5 dBm Pout 26 dBm @ EVM = 2.5% (PAR=9.17 dB) OIP3, 46 dBm Gain,17 dB Voltage, 8V Input Internally Matched 7X7mm Surface Mount Package Ideal for WiMAX Applications @ 5.8GHz
Functional Block Diagram
General Description
The XP1044-QL is a highly linear 2-stage power amplifier capable of 17 dB of gain, 3W of power at 1 dB compression and is housed in an RoHS compliant 7X7mm package. The XP1044-QL provides less than 2.5% EVM at 26 dBm output power with 802.16 OFDM signal and peak to average ratio 9.17 dB. The input and output of the device are internally pre-matched facilitating a simplified input and output match. This product operates off an 8V voltage supply and requires negative voltage which is used for current control. XP1044-QL is specifically designed for WiMAX applications between 4.9 GHz and 5.9 GHz.
Absolute Maximum Ratings
Supply Voltage RF Input Power* Storage Temperature Junctions Temperature Operating Temperature Thermal Resistance
+9.0V +23 dBm -55 to +125 C 175 C -40 to 85 C 24 C/W
Electrical Characteristics (T=25 oC,Voltage Supply=8V)
Parameter Frequency Range Power Gain Linear Power Input Return Loss Output IP3 @ 22dBm/Tone Noise Figure Output P1dB Operating Current Range Supply Voltage Negative Voltage 5.0
@ Pout = 27dBm @ EVM = 2.5%, OFDM, 802.16 PAR = 9dB
Unless otherwise specified, the following specifications are guaranteed at room temperature in a Mimix test fixture.
Condition
Min 4.9 15
Typ 5.8 17.0 26
Max 5.9
Units GHz dB dBm dB dBm dB dBm mA V V
Page 1 of 5
-10.0 44 46.0 5 34.5 1200 8.0 -0.7
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz 3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
P1044-QL
Typical Performance
XP1044-QL: ACPR vs. Output Power
WCDMA, Vdd = 8V, Idq1 = 440mA, Idq2 = 660mA (Idd = 1100mA) -30 4.9GHz -35 5.0GHz 5.1GHz 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 18 19 20 21 22 23 24 25 26 27 28
XP1044-QL: OIP3 vs. Output Power
Vdd = 8V, Idq1 = 550mA, Idq2 = 660mA (Idd = 1210mA)
4.9 GHz 5.0GHz 5.1GHz 5.2GHz 5.3GHz 5.4Hz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 6.0GHz
ACPR (dBc)
-40 5.2GHz -45 5.3GHz 5.4GHz -50 5.5GHz 5.6GHz -55 5.7GHz 5.8GHz -60 22.5 23 23.5 24 24.5 25 25.5 26 26.5 27 27.5 28 5.9GHz 6,0GHz
Output Power (dBm)
OIP3 (dBm)
Output Power Per Tone (dBm)
XP1044-QL: OIP3 vs. Output Power
Vdd = 8V, Idq1 = 440mA, Idq2 = 660mA (Idd = 1100mA) 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 18 19 20 21 22 23 24 25 26 27 28 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 18 20
XP1044-QL: OIP3 vs. Output Power
Vdd = 8V, Idq1 = 220mA, Idq2 = 660mA (Idd = 880mA)
4.9 GHz 5.0GHz 5.1GHz
4.9 GHz 5.0GHz 5.1GHz 5.2GHz 5.3GHz 5.4Hz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 22 24 26 28 6.0GHz
OIP3 (dBm)
5.2GHz 5.3GHz 5.4Hz 5.5GHz 5.6GHz 5.7GHz 5.8GHz 5.9GHz 6.0GHz
OIP3 (dBm)
Output Power Per Tone (dBm)
Output Power Per Tone (dBm)
XP1044-QL: P1dB vs. Freq Vdd = 8V
20
35 34.5 34 33.5
XP1044-QL: Gain Vs Freq Vdd = 8V
19 18 17 Gain(dB) 16 15 14
P1dB(dBm)
33 32.5 32 31.5 Idq1 = 440, Idq2 = 660mA 31 30.5 Idq1 = 550, Idq2 = 660mA
13 12
Idq1= 550, Idq2 = 660mA Idq1 = 440, Idq2 = 660mA
11
30 4.9 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6
10 4.9 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6
Freq (GHz)
Freq (GHz)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 2 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz 3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
P1044-QL
Pin Assignment:
Top View
Bottom View
Physical Dimensions
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 3 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz 3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
P1044-QL
App Note [1] Biasing - The XP1044-QL requires power supply sequencing. Negative voltage supply (Vgg) needs to be turned on first and then positive voltage can be applied to the drain (Vdd). When turning off the device, the positive supply (Vdd) should be turned off first and then negative voltage (Vgg) can be removed. The gate voltage is adjusted in order to set the drain current to the desired level. The gate voltage required to achieve a certain current can vary over temperature and from one device to another due to pinch-off voltage variation. Constant drain current can be achieved by Implementing an active bias circuit which allows for temperature compensation and eliminates the effect of pinch off voltage variation. The same current mirror circuit is implemented for each stage adding a total of 12 components at a cost of approximately $0.29
Application Circuit Schematic
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 4 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz 3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
P1044-QL Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human
body and the environment. For safety, observe the following procedures: Do not ingest. Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package
compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress.
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental
requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260C reflow) "Pb Free" processes.
Ordering Information
Description
XP1044-QL-0N00 XP1044-QL-EV1 Evaluation Board
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 5
Characteristic Data and Specifications are subject to change without notice. (c)2008 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.

▲Up To Search▲

Price & Availability of XP1044-QL-EV1

	To Download XP1044-QL-EV1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .